Cellar Pro 1800 Series Cooling Units

Standard wine cellar cooling unit with quiet operation.

Cooling capacity: up to 200 cu. ft.

The Cellar Pro 1800XT is the more powerful wine cellar cooling unit designed for more challenging environments.

Cooling capacity: up to 250 cu. ft.

Our most powerful 1800 Series wine cellar cooling unit, the Cellar Pro 1800 XTS is only 1 decibel louder than the 1800XT model.
Cooling capacity: up to 400 cu. ft.

Similar to the XTS series but the CellarPro 1800 XTSX wine cellar cooling unit can be mounted on Exterior walls and exposed to weather conditions ranging from 45-95 degrees.

Cooling capacity: up to 400 cu. ft.

The Cellar Pro 1800QTL is the quietest wine cellar cooling unit, providing outstanding performance and adjustable humidity control.

Cooling capacity: up to 80 cu. ft.
Recommended for Cabinet installations only.

With the bottle probe the cooling unit cycles on and off with regards to the temperature in the bottle as opposed to the temperature in the wine cellar.

Remote display / Control unit

Allows control panel to be in a different location than the cooling unit. 

Top Vent Option
Standard configuration for a Cellar Pro sold on its own is Back Vent.
You can easily modify on your own to top vent or rear vent.
Choose this option if you want the factory to change the plate for you.

There is no cost for this option, you just need to let us know!

Also known as: Drain Line & Heating Element.  

Get this option for High humidity environments. 

1/2" ID condensate fitting for 1800 Series wine cooling units.

10 foot drain line.

Also known as Compressor Heater.

Cellar Pro's Crankcase Heater is required if the condenser (rear) of the cooling unit is exposed to temperatures below 40°F - but not lower than 20°F.

Low Ambient Kit allows for cooling units including the VS Series, 1800 Series, Splits and Air Handler Series, to operate in temperatures as low as  -20°F.

Kit includes Compressor Heater & Fan Cycle Switch.

Cellar Pro has created a rear duct for CellarPro 1800 Series cooling units that allows warm intake/exhaust to be ducted up to 100 equivalent feet (50 feet per duct).

When used with Cellar Pro's 1800 Series cooling units, the Front Intake Hood allows for the cooling unit to be installed above the wine cellar.

Standard configuration for the 1800 is for the cord to come out the back of the unit on the warm side.

This Cord IN option allows the power cord to be routed from the side, within the cabinet or cellar. (Location will then be Left Side, just below the Electrical Receptacle).

ONLY needed if this replacement cooling unit is NOT being installed in a Le Cache unit.
Mounting clips for bolting 1800XTS wine cooling units to the ceiling inside a wine cellar or cabinet.

Uniquely designed metal and poly-coated filter frames made to fit over the condenser coils of all Cellar Pro cooling units.

Dimensions: 13"W x 1"D x 9"H

*FRAME ONLY - Only needs to be purchased ONCE*

• Power/Rating:noinfofound
• Warranty:noinfofound

  This is the Frame only – only needs to be purchased one. 

  This is the Frame only – only needs to be purchased one. 

  This is the Frame only – only needs to be purchased one. 

  This is the Frame only – only needs to be purchased one. 

High-performance replacement air filters designed to fit over all CellarPro 1800 cooling units.

Eliminates the need to clean the coils.

Price is for a pack of 2 filters.

Fluorescent Light added to Cellar Pro cooling unit.

Cellar Pro's Louvered Grill can be painted, mounted and used outside the cellar to hide the rear of 1800 wine cooling units.

Dimensions (WxDxH): 20" x ¼" x 12" (in)

Cellar Pro's Louvered Wood Grill Cover is designed to fit over all CP 1800 wine cellar refrigeration systems.
 

Air deflector redirects either hot-air or cold-air exhaust.

Dimensions (WxDxH): 10"-14" x 3 ½" x 2 ½" (in)

208-230V - 50Hz/60Hz version of the 1800XT